IC600BF808

GE Fanuc | Series Six | In Stock Ships Today GE Fanuc Series Six IC600

IC600BF808 Image

IC600BF808

Same Day - Free Shipping

  • Manufacturer: GE Fanuc
  • Description: 8 points Interrupt Input Module
  • Weight: 3 lbs :: ≈ 2 kgs
  • Warranty: 1 Years
  • Product Revisions Available:
  • Other Available Revisions of the IC600BF808 : A, B, C, D, E, F, G, H, I, J, K, L, M, N, O, P, Q, R, S, T, U, V, W, X, Y, Z,

Product Manual Excerpt

GENERAL DESCRIPTION The Interrupt Input module allows the user to initiate the execution of a subroutine by activating an input. (A subroutine can also be initiated by a user-program function.) By Series Six convention, a subroutine is a sequence of functions separate from the main program that is solved, only when required, by the Programmable Controller. The Interrupt Input module can be utilized in a CPU I/O station or a Local I/O station. A Model 60 CPU or Model 600 CPU can support one Interrupt Input module, whereas a Model 6000 CPU can support two modules: one in a primary I/O chain, another in an auxiliary I/O chain. The Interrupt Input module features and benefits are summarized in Table 1. Each module provides eight inputs. The inputs are organized into four groups of two, with an isolated neutral for each group. In series with each input is an LED that indicates current flow through the input circuit. The inputs can respond to rising-edge transitions or falling-edge transitions. The edge response of an individual input is jumper-selectable by the user . In a primary I/O chain, the module inputs, Nos.l-8 (I/O points I1001-Il008), correspond to subroutines, Nosl-8, resident in the user program. However, in an auxiliary I/O chain (which can only be connected to a Model 6000 CPU), the module inputs, Nos.l-8 (I/O p o i n t s 11009-11016), correspond to subroutines, Nos.9-16, in the user program. Interrupts are serviced by the CPU on a first-come, firstserve basis. When two or more interrupts occur simultaneously, the lowest-numbered interrupt is serviced first. Refer to Figure 1 (next page) for Interrupt Input module specifications. TABLE 1. FEATURES AND BENEFITS FEATURES BENEFITS 300 usec Input Filtering. Four Isolated sets of two inputs. Jumper-selectable response to user device. Rapid response for high-speed input processing. Can use a different power source for every 2 inputs. Responds to off-to-on transitions or on-to-off transitions. APPLICATIONS - Position Control - Emergency Stops - High-Speed Packaging Interrupt Input Module GEK-83524 - Dimensions: Circuit Board: 8.15 x 11.0 x 1.20 (inches) 208 x 280 x 31 (mm) Faceplate: 12.46 x 1.175 (inches) 317 x 30 (mm) - Power Requirements: 5V DC, 225 mA (Max.) (Supplied by I/O Rack Power Supply) - Storage Temperature: 0 - 70 C - Operating Temperature: 0 - 60 C - Humidity: 5% - 95% (non-condensing) - Card Filtering: Off-On Delay: 300u s (max.) On-Off Delay: 8 ms (min.) 10 ms (typ.) 12 ms (max.) - User Power Source: l0-30V DC Interrupt OFF Condition: 3V DC Interrupt ON Condition: 1OV DC FIGURE 1. SPECIFICATIONS INT RUPT lN?Uf @ LED 1 - LED 8: LED numbers correspond to interrupt-input numbers. Active LED (ON) indicates current flow through the input circuit. Jumper 1 - Jumper 8: Jumper numbers correspond to interrupt-input numbers. Jumper at N terminal causes corresponding interrupt input to respond to rising edge. Jumper at I terminal causes corresponding interrupt-input to respond to falling edge. FIGURE 2. USER ITEMS 2 Ref. PC-S6-84-0168 Interrupt Input Module GEK-83524 INSTALLATION The Interrupt Input module can be installed in any position of an I/O rack in a CPU I/O station or Local I/O station. (A Model 60 CPU-based system contains I/O slots within the CPU rack.) The module address is hardwired on the circuit board to equal 125, decimal (FD, hexadecimal). Consequently, the values of the DIP switches on the rack backplane adjacent to the I/O slot are ignored by the CPU. Before inserting the module in the I/O rack, the user should inspect the placement of the eight, blue-plastic jumpers on the circuit board (Refer to Figure 2, User Item No. 2). These jumpers allow the user to select the edge responses of the eight inputs. The module is shipped from the factory with the eight inputs set to respond to rising-edge transitions. (The jumpers are inserted between middle terminals and the N terminals.) The user can direct any given input to respond to a falling-edge transition by inserting the associated jumper between the middle terminal and the I terminal. We recommend that you use the extraction/insertion tool furnished with your CPU to remove or install the circuit board. With the board in place in the rack, the edge connector on the faceplate should be slipped over the circuit board so that proper contact is made. You can then NOTE No Isolation: All inputs on one 10 - 30V DC supply secure the faceplate to the rack using the thumbscrews at the bottom and top. Refer to Figure 3, Typical User Connections. The Interrupt Input module inputs are connected to user-provided 10 - 30V DC power supplies. The switching device that activates an input must be in series with the power supply. In this scheme, one side of the switching device is connected to the input, the other side is connected to the positive terminal of the 10 - 30V DC supply; the negative terminal of the power supply is connected to the neutral terminal associated with the input. For the purpose of electrical isolation, as few as two inputs can be connected to a single 10 - 30V DC supply. Otherwise, up to eight inputs can be connected to a single lo- 30V DC supply. NOTE We recommend that you power-down your Series Six Programmable Controller before installing or removing the Interrupt Input module. A parity error could result at any address in the I/O structure if you do not power-down as recommended. N2 NOTE Maximum Isolation: Two inputs on each 10 --c 30V DC supply FIGURE 3. TYPICAL USER CONNECTIONS Interrupt Input Module GEK-83524 Circuit Board & Faceplate IC600BF808B ORDERING INFORMATION Circuit Board IC600YB808B Faceplate IC600FP808A CATALOG NUMBER REVISION SUFFIX The equipment listed above having the catalog numbers shown and the same equipment having a higher alpha suffix is designed for listing by UL for use as auxiliary control devices. The equipment is a direct replacement for equipment having the same catalog number but a lower alpha suffix. This symbol on the nameplate means the product is listed by Underwriters Laboratories Inc. (UL Standard No. 508, Industrial Control Equipment, subsection Electronic Power Conversion Equipment.) For further information, contact your local GE Fanuc sales office. GE FANUC AUTOMATION NORTH AMERICA, INC., CHARlOTTESVltLE, VIRGINIA

Need To Order A Specific Revision?

Give us a call at 1-800-360-6802 or 1-919-535-3180. We can help you with your Revision specific needs.


UPS Ground shipping is always FREE!


What is New Surplus?

These “New Surplus” units are a great cost saving alternative. This product is in the original manufacturer’s packaging with all sub-assemblies and documentation. Comes with a PLC Distribution Factory & Supply 3-year warranty.


UPS Ground shipping is always FREE!


What is Surplus New?

Surplus New - New unused and includes all sub-assemblies and documentation. Product may ship in manufacturer or PLC Distribution Factory & Supply packaging and includes a PLC Distribution Factory & Supply 3 Year Warranty.


UPS Ground shipping is always FREE!


What is Reconditioned?

Reconditioned products from PLC Distribution Factory & Supply are a cost-effective alternative to new and obsoleted PLC products. Every part is reconditioned down to the circuit board level. All parts are thoroughly inspected and hand-cleaned before being functionally tested in a fully configured system.


Our Reconditioned Products always come with a PLC Distribution Factory & Supply 2-Year Warranty.

UPS Ground shipping is always FREE!


110% PRICE MATCH GUARANTEE


We stand behind our prices with a 110% price match guarantee. If you buy a part from us and, within seven days of purchase, find that part advertised on an authorized distributor's website for less, simply contact us and give us a link to the lower advertised price and we'll refund you 110% of the difference between your purchase price and the advertised lower price. The part must be in-stock for immediate shipment and be in similar condition. All pricing must be displayed without signing in.

Repair Service


3-5 Days for most repairs. 24 hour repair upon request at no extra charge. If part is unrepairable, we will exchange with a working unit or return unrepaired.