GE Fanuc | Series Six | In Stock Ships Today GE Fanuc Series Six IC600

IC600BF905 Image


Same Day - Free Shipping

PDF Electric & Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply.

Product comes with PDF Electric & Supply's 1-year warranty.

  • Manufacturer: GE Fanuc
  • Description: 8 points 230Vac Output Module
  • Weight: 3 lbs :: ≈ 2 kgs
  • Warranty: 1 Years
  • Product Revisions Available:
  • Other Available Revisions of the IC600BF905 : A, B, C, D, E, F, G, H, I, J, K, L, M, N, O, P, Q, R, S, T, U, V, W, X, Y, Z,

Product Manual Excerpt

GENERAL DESCRIPTION The AC output modules function as discrete switching devices between user AC power sources and user loads. The modules are available in two versions: 11 S Vac and 230 Vac. The features and benefits of these modules are summarized in Table 1. A module contains eight outputs, divided into two groups, each group capable of connecting a common power source. Each output circuit utilizes a TRIAC as a switching device that connects the associated output terminal to the high side of the user power source when the output is in the ON state. Provision is made in the Series Six Programmable Controller (PC) to automatically disable the outputs of the AC Output modules in the event of an Input/Output I/O chain failure or a Central Processor Unit (CPU) failure. Visible through a lens on the faceplate are pairs of neon lamps associated with each output. One lamp indicates that the output is in the ON state; the other indicates the status of a fuse also included in each of the eight output circuits. TABLE 1. FEATURES AND BENEFITS FEATURES Two modules available: ??115Vac ?? 230Vac BENEFITS Useful in a variety of applications Indicator lights for each output: ?? ON/OFF light ?? Blown Fuse light Simplifies troubleshooting. Eight inputs per module. Optically-coupled inputs. Efficient use of I/O rack space. Provides electrical isolation between power sources and Series Six PC. * Solenoids * Indicator lights APPLICATIONS * Motors * Motor starters e 115 VAC OUTPUT BF BF kos FAB.NO .717645-001 :2 4ABE IN U.S., PC-56-84 .0117 1 AC Output Modules GEK-83514 Power Requirements: 5V DC, 535 mA maximum Supplied by I/O power supply. Dimensions: Circuit Board: 8.15 x 11.0 x 1.20 (inches) User-Supplied 208 x 280 x 31 (mm) Module Voltage Leakage (OFF) Faceplate: 12.46 x 1.175 (inches) 115V AC 90-130V AC I.7mA 115V 317 x 30 (mm) 230V AC 180-260V AC 1.0mA 230V Inrush Current: 12 A for 33 ms (max.) ON-State Current: Maximum: 2 A @ 40 C (Derate to 50% duty cycle @ 60 C). Minimum: 5 mA ON-State Voltage Drop: 1.5V typical 2.5V max. Humidity: 5-95% (non-condensing) Storage Temperature: -20 to +80 C ON Delay: less than 1 ms OFF Delay: Less than 1/2 cycle Number of Outputs: Eight (8), in two groups of 4 outputs with common high and neutral connections. Operating Temperature: 0-60 C (at the outside of the rack) FIGURE 1. SPECIFICATIONS FIGURE 2. USER ITEMS 2 Ref. PC-S6-0117 AC Output Modules GEK-83514 @ Terminal Cover 02 User Terminal Block: Accepts connections from user output devices and the AC power source(s). See the Installation section of this Data Sheet. 03 Circuit-Board Terminal Block: Mates with the user termina1 block. @ Output Lights: 1 through 8 Off: Corresponding output is in the ON state. Off: Corresponding output is in the OFF state. 0 BF (Blown Fuse) Lights On: The fuse for corresponding output is open (blown). Off: The fuse for corresponding output is OK. @ Output-Circuit Fuses (3 A normal blow). FIGURE 2. USER ITEMS (Part 2 of 2) INSTALLATION The AC Output modules can be installed in an I/O rack or the I/O rack section of the Model 60 Central Processor Unit (CPU). Follow these steps: In reference to Figure 3, note that wires connected to the N1 terminals are at the same potential, as are wires connected to the N2 terminals. Set the Dual-In-Line Package (DIP) switches directly behind the card slot on the rack backplane to establish the correct correspondence between the input terminals on this module and a group of eight consecutive input numbers in the user program. For further information on I/O DIP switch settings. refer to the lnstallation section of the Series Six Installation and Maintenance Manual (GEK-25361). Use the extraction/insertion tool furnished with the Series Six CPU to insert (or remove> this module in the card slot. Guide the faceplate over the circuit board so that the terminals near the bottom of each are mated; secure the faceplate to the rack using the thumbscrews at the top and bottom. Refer to Figure 3. Connect one side of the user circuit to the appropriate input terminal (1 through 8). Circuits connected to inputs 1 through 4 must have their opposite sides connected to either of the Nl terminals. Likewise, circuit connected to inputs 5 through 8 must have their opposite sides connected to either of the N2 terminals. Each input terminal can accommodate one No. 12 AWG wire or two No. 14 AWG wires. 5 . Guide the terminal cover onto the top of the terminal block, then slide it downward over the terminals. A markable area is provided on the plastic lens beside each Light-Emitting Diode (LED) for noting the function or source of each input. The faceplates are color coded: Yellow: Red: 115 Vac 230 Vac OUTPUT iti 1 2 3 4 N1 H2 E N2 PC 56 84-0, \' AC Output Modules GEK-83514 I WARNING Voltages from user field devices may be present on the faceplate terminals, even if the power supply in the I/O rack is off. Care should be taken when handing the faceplate of this module or any wires connected to it. FIGURE 3. TYPICAL USER OUTPUT CONNECTIONS ORDERING INFORMATION Module Circuit Board and Faceplate Circuit Board Faceplate 115 Vac IC600BF904B IC600YB904B IC600FP904B 230 Vac IC600BF905B IC600YB905B IC600FP905B CATALOG NUMBER REVISION SUFFIX The equipment listed above having the catalog numbers shown and the same equipment having a higher alpha suffix is designed for listing by UL for use as auxiliary control devices. The equipment is a direct replacement for equipment having the same catalog number but a lower alpha suffix. This symbol on the nameplate means the product is listed by Underwriters Laboratories Inc. (UL Standard No. 508, Industrial Control Equipment, subsection Electronic Power Conversion Equipment.) For further information, contact your local GE Fanuc sales office. GE Fanuc Automation North America, Inc., Charlottesville, Virginia

Need To Order A Specific Revision?

Give us a call at 1-800-360-6802 or 1-919-535-3180. We can help you with your Revision specific needs.

UPS Ground shipping is always FREE!

What is New Surplus?

These “New Surplus” units are a great cost saving alternative. This product is in the original manufacturer’s packaging with all sub-assemblies and documentation. Comes with a PDF Electric & Supply 3-year warranty.

UPS Ground shipping is always FREE!

What is Surplus New?

Surplus New - New unused and includes all sub-assemblies and documentation. Product may ship in manufacturer or PDF Electric & Supply packaging and includes a PDF Electric & Supply 3 Year Warranty.

UPS Ground shipping is always FREE!

What is Reconditioned?

Reconditioned products from PDF Electric & Supply are a cost-effective alternative to new and obsoleted PLC products. Every part is reconditioned down to the circuit board level. All parts are thoroughly inspected and hand-cleaned before being functionally tested in a fully configured system.

Our Reconditioned Products always come with a PDF Electric & Supply 2-Year Warranty.

UPS Ground shipping is always FREE!

Repair Service

3-5 Days for most repairs. 24 hour repair upon request at no extra charge. If part is unrepairable, we will exchange with a working unit or return unrepaired.