GE Fanuc | Series Six | In Stock Ships Today GE Fanuc Series Six IC600

IC600BF906 Image


Same Day - Free Shipping

PDF Electric & Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply.

Product comes with PDF Electric & Supply's 1-year warranty.

  • Manufacturer: GE Fanuc
  • Description: 8 points 12Vdc Sink Output Module
  • Weight: 3 lbs :: ≈ 2 kgs
  • Warranty: 1 Years
  • Product Revisions Available:
  • Other Available Revisions of the IC600BF906 : A, B, C, D, E, F, G, H, I, J, K, L, M, N, O, P, Q, R, S, T, U, V, W, X, Y, Z,

Product Manual Excerpt

General Description The discrete (OFF/ON), 8-point DC Output module can be utilized in an I/O rack, or in any of the I/O slots in a Model 60 Central Processor Unit (CPU), to provide an optically isolated interface between the backplane I/O bus and user output devices. The first four outputs are grouped to share a common power source, as are the second four outputs. The module for each output-voltage range is available in either a source or a sink version. The DC Output modules features and benefits are summarized in Table 1. When using a sink module, current must flow through the load into the output terminal of the module. When using a source module, current is provided by the module and the current flows out of the module to the load. Each of the eight output drivers uses a Darlington amplifier as a switching device. The circuit board also contains comparator circuitry that determines if the module is being addressed and a buffer where the output data is stored and presented to the output drivers. Provision is made to automatically disable the entire group of output drivers in the event of an I/O-chain, or CPU, failure. Light-Emitting Diode (LED) indicators display the state (ON/OFF) of each output, and the condition of the individual output-circuit fuses. Refer to Table 2 for DC Output module specifications. Table 1. Features and Benefits Features Three switching ranges available: 20 Vdc. 40 Vdc. 55 Vdc. Benefits Useful in a variety of applications. Provides output capability with existing user power supplies and devices. Each available in Source or Sink configuration. Eight Output points per module. I Efficient use of I/O rack space. Optically-coupled Output drivers. Provides electrical isolation between user field devices and the Series Six Controller. Applications - High-speed switching: - Solenoid valves. - Battery-powered I/O systems. Annunciators. Indicators. Relays. 2 DC Output Modules -~ GEK-83521B 1. Terminal Cover 4. Output LED 1 + 8 Figure 1, User ltems 2. User Terminal Block: Accepts connections from user output devices and the DC power source(s). (Refer to Figure 2, Typical User Connections.) 3. Circuit-Board Terminal Block: Mates with the user terminal block. Installation The DC Output module can be installed in an I/O rack or in a model 60 CPU rack. Before installing the module, set the Dual-In-Line-Package (DIP) switches directly behind the card slot on the rack backplane to establish the proper correspondence between the output terminals on this module and a group of eight consecutive output numbers in the program. To determine the proper switch settings, refer to the table in the Installation section of the Series Six Installation and Maintenance Manual, GEK-25361. We recommend that he extraction/insertion tool furnished with the CPU be used to remove or install the circuit board. With the board in place in the rack, the On: Corresponding output is in the ON state. Off: Corresponding output is in the OFF state. 5. BF (Blown Fuse) LED 1 + 8 On: The fuse for corresponding output is open (blown) 1 Off: The fuse for corresponding output is OK. 6, Output-Circuit Fuses: 3 A, normal blow (AGC 3) faceplate should be slipped over the circuit board so that the terminals near the bottom of each are mated. The faceplate can then be secured to the rack using the thumbscrews at top and bottom. Refer to Figure 2 for typical user connections to the DC Output module. One side of each load controlled by this module should be connected to the appropriate output terminal (1 through 8). The other side of each load connected to terminals 1 through 4 should be returned to a common line connected to the Neutral No.1 (N1) terminal for a source module, or to the High No.1 (Hl) terminal for a sink module. The other side of each load connected to terminals 5 DC Output Modules 3 GEK-83521B through 8 should be returned to a common line connected to the Neutral No.2 (N2) terminal for a source module, or to the High No.2 (H2) terminal for a sink module. A user DC power source must be connected between the Hl (+) and the Nl (-) terminals; a power source must also be connected between the H2 (+) and the N2 (-) terminals. Each terminal can accommodate one No.12 AWG wire or two No.14 AWG wires. The terminal cover should be installed by _---r--t-IHlI Nl 6 N 2 L 1 DC Source Module User Wiring guiding both of its edges onto the top of the terminal block and sliding it downward over the terminals. Note that a markable area is provided on the plastic lens beside each pair of indicators for noting the function or destination of each output. The faceplates are color coded (blue) to allow you to easily distinguish the DC Output modules from other types of I/O modules. Hl H 2 8 N 2 LEGEND S: Output Switching Device L: User Load E: User Power Source (DC) DC Sink Module User Wiring Figure 2. Typical User Connections 4 DC Output Modules GEK-83521B Table 2. Specifications - Dimensions: - Power Requirements: - Number of Outputs: - Leakage (OFF): - Steady State Current: - Inrush Current: - Total ON-State Current per Module: - ON-State Voltage Drop: - Response Time: - Operating Temperature: - Humidity: Circuit Board: 8.15 x 11.0 x 1.20 (inches) 208 x 280 x 31 (mm) Faceplate: 12.46 x 1.175 (inches) 317 x 30 (mm) 5 Vdc, 400 mA (maximum) Supplied by I/O-rack power supply. Module User-Supplied Voltage 12 Vdc 9 + 20 Vdc 24 Vdc 19 + 40 Vdc 48 Vdc 38 -3 55 Vdc Eight (8), in two groups of 4 outputs with common high and neutral connections. 5 mA @ 60 C (maximum) 2 A (maximum) 7 A (maximum) Maximum: 16 A @ 0-4OC, 8 A @ 60 C Minimum: 0 A 2.25 V (maximum) 1 ms (maximum) 0 - 60 C (at the outside of the rack) -20 to +8OC 5 - 95% (non-condensing) Table 3, Ordering Information Module Circuit Board & Faceplate Circuit Board Faceplate 12 Vdc Output (Source) 24 Vdc Output (Source) 48 Vdc Output (Source) 12 Vdc Output (Sink) 24 Vdc Output (Sink) 48 Vdc Output (Sink) IC600BF907B IC600BF908B IC600BF909B IC600BF906B IC600BF902B IC600BF903B IC600YB907B IC600YB908B IC600YB909B IC600YB906B IC6OOYB90202B IC600YB903B IC600FP907B IC600FP908B IC600FP909B lC600FP906B IC600FP902B IC600FP903B Catalog Number Revision Suffix The equipment listed above having the catalog numbers shown and the same equipment having a higher alpha suffix is designed for listing by UL for use as auxiliary control devices. The equipment is a direct replacement for equipment having the same catalog number but a lower alpha suffix. The UL symbol on the nameplate means the product is listed by Underwriters Laboratories Inc. (UL Standard No. 508, Industrial Control Equipment, subsection Electronic Power Conversion Equipment.) For further information, contact your local GE Fanuc sales office. GE Fanuc Automation North America, Inc., Charlottesville, Virginia

Need To Order A Specific Revision?

Give us a call at 1-800-360-6802 or 1-919-535-3180. We can help you with your Revision specific needs.

UPS Ground shipping is always FREE!

What is New Surplus?

These “New Surplus” units are a great cost saving alternative. This product is in the original manufacturer’s packaging with all sub-assemblies and documentation. Comes with a PDF Electric & Supply 3-year warranty.

UPS Ground shipping is always FREE!

What is Surplus New?

Surplus New - New unused and includes all sub-assemblies and documentation. Product may ship in manufacturer or PDF Electric & Supply packaging and includes a PDF Electric & Supply 3 Year Warranty.

UPS Ground shipping is always FREE!

What is Reconditioned?

Reconditioned products from PDF Electric & Supply are a cost-effective alternative to new and obsoleted PLC products. Every part is reconditioned down to the circuit board level. All parts are thoroughly inspected and hand-cleaned before being functionally tested in a fully configured system.

Our Reconditioned Products always come with a PDF Electric & Supply 2-Year Warranty.

UPS Ground shipping is always FREE!

Repair Service

3-5 Days for most repairs. 24 hour repair upon request at no extra charge. If part is unrepairable, we will exchange with a working unit or return unrepaired.