GE Fanuc | Series Six | In Stock Ships Today GE Fanuc Series Six IC600

IC600CB524 Image


Same Day - Free Shipping

PDF Electric & Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply.

Product comes with PDF Electric & Supply's 1-year warranty.

  • Manufacturer: GE Fanuc
  • Description: Arithmetic Control Module
  • Weight: 3 lbs :: ≈ 2 kgs
  • Warranty: 1 Years
  • Product Revisions Available:
  • Other Available Revisions of the IC600CB524 : A, B, C, D, E, F, G, H, I, J, K, L, M, N, O, P, Q, R, S, T, U, V, W, X, Y, Z,

Product Manual Excerpt

GFK-0144 Arithmetic ControI Module November 1987 GENERAL DESCRIPTION The Arithmetic Control module performs arithmetic and logical operations for the Series Six Central Processor Unit (CPU). The features and benefits of this module are summarized in Table 1. Four, AM2903, bit-slice, integrated circuits contained on this module constitute a 16-bit microprocessor that works in conjunction with the Logic Control module to generate system control and timing signals. The Arithmetic Control module is linked to the Logic Control through a ribbon cable connector. Visible through a lens on the faceplate are two Light Emitting Diode (LED) indicators: One, marked \"CHECK , remains lit to indicate that a self-test has been completed successfully once per I/O sweep; this LED also indicates that no abnormal conditions prevail in the CPU, such as system clock stopped, scan time longer than 300 milliseconds. The other LED, marked RUN indicates that the CPU is performing execution sequences and is in the RUN mode. The LEDs operate only when the module is installed in a properly powered CPU rack. Refer to Table 2 for Arithmetic Control module specifications Table 1. FEATURES AND BENEFITS FEATURES Contains 2 LED indicators: *CHECK *RUN BENEFITS Indicates status of CPU to simply troubleshooting. Usable in Model 60, 600, 6000 and Series Six Plus CPUs. Reduces spare-parts inventory. Bit-slice architecture. Supports all Series Six Instructions sets including Expanded II High-speed processing. Increased functionality and backwards compatability. e ARITH CONTROL RUN CHECK e 2 Arithmetic Control Module GFK-0144 Figure 1. USER ITEMS 1. Socket for ribbon-cable connection to Logic Control module. See the \"Installation\" section of this sheet. 2. RUN Light On: CPU execution sequence is proceeding; the self test is passed and the I/O scan is completed at least once each 300 (+/-50 ms). CPU is in RUN mode. Off: CPU is in STOP mode. 3. CHECK Light On: CPU execution sequence is proceeding; the self-test is passed at least once each 300 ms (+/-50 ms). CPU could be in RUN or STOP mode. Off: CPU self-test has not been passed within 300 ms (+/-50 ms) or user program execution takes longer than 300 ms. CPU goes to STOP mode; I/O chain is reset. Arithmetic Control Module 3 GFK-0144 INSTALLATION 3. Fasten the faceplate to the rack using the screws at The Arithmetic Control module can be installed in a Model 60, 600, 6000 or Series Six Plus CPU. Follow these steps for all models: 1. Use the extraction/insertion tool supplies with the CPU to insert (or remove) this module into the appropriate slot. the top and bottom. NOTE Attempting to operate the system without the ribbon cable connected between the Arithmetic Control module and the Logic Control module will cause the CPU to operate unpredictablv. 2. Connect a short length of ribbon cable (also supplied with the CPU) between this module and the Logic Control module. Table 2. SPECIFICATIONS Dimensions: Circuit Board: Faceplate: Power Requirements: Storage Temperature: Operating Temperature: 8.15 x 11.0 (inches) 208 x 280 (mm) 12.46 x 1.175 (inches) 317 x 30 (mm) 5V DC, 1.7A (Supplied by CPU power supply) -20 to 70 C (-4 to 158 F) 0 to 60 C (32 to 140 F) (outside rack) Humidity: 5% - 95% (non-condensing) 4 Arithmetic Control Module - GFK-0144 Table 3. ORDERING INSTRUCTIONS DESCRIPTION CATALOG NUMBER Circuit Board and Faceplate Faceplate IC6OOCB524K IC600FT 500A CATALOG NUMBER REVISION SUFFIX The equipment listed above having the catalog numbers shown and the same equipment having a higher alpha suffix is designed for listing by UL for use as auxiliary control devices. The equipment is a direct replacement for equipment having the same catalog number but a lower alpha suffix. For further information, contact your local GE Fanuc sales office. GE Fanuc Automation North America, Inc., Charlottesville, Virginia

Need To Order A Specific Revision?

Give us a call at 1-800-360-6802 or 1-919-535-3180. We can help you with your Revision specific needs.

UPS Ground shipping is always FREE!

What is New Surplus?

These “New Surplus” units are a great cost saving alternative. This product is in the original manufacturer’s packaging with all sub-assemblies and documentation. Comes with a PDF Electric & Supply 3-year warranty.

UPS Ground shipping is always FREE!

What is Surplus New?

Surplus New - New unused and includes all sub-assemblies and documentation. Product may ship in manufacturer or PDF Electric & Supply packaging and includes a PDF Electric & Supply 3 Year Warranty.

UPS Ground shipping is always FREE!

What is Reconditioned?

Reconditioned products from PDF Electric & Supply are a cost-effective alternative to new and obsoleted PLC products. Every part is reconditioned down to the circuit board level. All parts are thoroughly inspected and hand-cleaned before being functionally tested in a fully configured system.

Our Reconditioned Products always come with a PDF Electric & Supply 2-Year Warranty.

UPS Ground shipping is always FREE!

Repair Service

3-5 Days for most repairs. 24 hour repair upon request at no extra charge. If part is unrepairable, we will exchange with a working unit or return unrepaired.